eMaxMobileApp

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com. TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano! Please have a look on the news section of www.eMax-Tuning.com/home-en#news or contact us via info@eMax-Tuning.com. Also please check the document https://www.emax-tuning.com/eMax-possibilities.pdf for the tuning possibilities which are highly depending on the drive unit type and currently installed motor firmware version. This version 1.88 for STePS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit. This version is capable to optimize DU-EP801, DU-E800, DU-EP600, DU-E80X0, DU-E7000, DU-E6XXX and DU-E50X0 drive units as well as its variants "RS" and "CRG". new in version 1.88 (26.08.25): - partial compatibility for EP801/EP6 motor firmware 4.4.2 new in version 1.87 (23.08.25): - minor optimizations new in version 1.86 (10.08.25): - new battery types added, minor bugfix and optimizations new in version 1.85 (10.02.25): - minor bugfix and optimizations new in version 1.84 (25.01.25): - partial compatibility for EP801/EP6 motor firmware 4.4.1 - optimizations and improvements new in version 1.83 (07.09.24): - bug fix for crash on some very rare bike configurations at 73% of bike information reading new in version 1.82 (31.08.24): - optimizations and minor bug fixes for DU-EP800 new in version 1.77 (30.06.24): - partial compatibility for EP801/EP6 motor firmware 4.3.0 new in version 1.76 (15.06.24): - new battery types and RS default values for generation 2 added new in version 1.75 (12.06.24): - bugfix for DU-E8000 motor firmware 4.10.0 new in version 1.74 (20.05.24): - partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0 - partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0 - partial compatibility for DUE7000 FW 4.8.0 - partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0 - partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0 See also https://www.emax-tuning.com/eMax-possibilities.pdf new in version 1.73 (15.04.24): - partial compatibility for EP801/EP motor firmware 4.2.2 new in version 1.72 (26.03.24): - partial compatibility for EP801/EP motor firmware 4.2.1 new in version 1.71 (09.02.24): - partial compatibility for EP801/EP motor firmware 4.2.0 - minor optimizations new in version 1.70 (23.10.23): - minor bug fix new in version 1.69 (09.10.23): - minor improvements, change of EP801/EP6 message dialog texts new in version 1.68 (29.09.23): - adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10 new in version 1.67 (11.09.23): - bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11 new in version 1.66 (07.09.23): - adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1 - adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1 - adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11 - adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5 - adaption to DUE7000 FW 4.7.7 - adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7 new in version 1.65 (02.09.23): - EP801/EP6 change of max. peak power and max. torque range added - EP801/EP6 "reduced max. speed setting" enabled and enhanced - EP801/EP6 "motor angle setting" enabled - SC-EN500 display added - new cassette types added (just for reading) - correction in EP8xx performance view site with jump to next edit field - bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button